EN 14541-1:2022
(Main)Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
This document specifies the general terms and definitions relevant for the utilization of thermoplastics recyclates in thermoplastics pipes, fittings and ancillaries for both pressure and non-pressure piping systems.
This document is intended to be used by specification writers in conjunction with CEN/TS 14541-2 when preparing normative documents under the scope of CEN/TC 155.
Kunststoff-Rohrleitungen und -Formstücke - Verwendung von thermoplastischen Rezyklaten - Teil 1: Begriffe
Dieses Dokument legt allgemeine Begriffe fest, die bei der Verwendung von thermoplastischen Rezykla¬ten in thermoplastischen Rohrleitungen, Formstücken und Zubehörteilen sowohl in druckbeaufschlagten als auch in drucklosen Rohrleitungssystemen von Bedeutung sind.
Die Verwendung dieses Dokument ist in Verbindung mit CEN/TS 14541-2 bei der Erarbeitung von normativen Dokumen¬ten innerhalb des Geltungsbereiches von CEN/TC 155 zur Nutzung durch Verfasser von Spezifikationen vorgesehen.
Tubes et raccords en plastique - Utilisation de recyclats thermoplastiques - Partie 1 : Vocabulaire
Le présent document spécifie les termes généraux et définitions pertinents pour l'utilisation des recyclats thermoplastiques dans les tubes, les raccords et les accessoires en thermoplastique pour les systèmes de canalisations sous pression et sans pression.
Le présent document est destiné à être utilisé par les rédacteurs de spécifications conjointement avec la CEN/TS 14541-2 lors de la préparation de documents normatifs dans le domaine d'application du CEN/TC 155.
Polimerne cevi in fitingi - Uporaba recikliranih plastomerov - 1. del: Terminologija
Ta dokument določa splošne izraze in definicije, ki se navezujejo na uporabo recikliranih plastomerov v plastomernih ceveh, fitingih ter pomožnih delih pri tlačnih in netlačnih cevnih sistemih.
Ta dokument naj bi uporabljali avtorji specifikacij v povezavi s standardoma prCEN/TR 14541-2 in prCEN/TR 14541-3 pri sestavljanju normativnih dokumentov, ki spadajo na področje uporabe standarda CEN/TC 155.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 14541-1:2022
01-julij-2022
Nadomešča:
SIST-TS CEN/TS 14541:2013
Polimerne cevi in fitingi - Uporaba recikliranih plastomerov - 1. del: Terminologija
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
Kunststoff-Rohrleitungen und -Formstücke - Verwendung von thermoplastischen
Rezyklaten - Teil 1: Begriffe
Tubes et raccords en plastique - Utilisation de recyclats thermoplastiques - Partie 1 :
Vocabulaire
Ta slovenski standard je istoveten z: EN 14541-1:2022
ICS:
01.040.23 Tekočinski sistemi in sestavni Fluid systems and
deli za splošno rabo (Slovarji) components for general use
(Vocabularies)
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST EN 14541-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 14541-1:2022
---------------------- Page: 2 ----------------------
SIST EN 14541-1:2022
EN 14541-1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2022
EUROPÄISCHE NORM
ICS 83.140.30 Supersedes CEN/TS 14541:2013
English Version
Plastics pipes and fittings - Utilisation of thermoplastics
recyclates - Part 1: Vocabulary
Tubes et raccords en plastique - Utilisation de recyclats Kunststoff-Rohrleitungen und -Formstücke -
thermoplastiques - Partie 1 : Vocabulaire Verwendung von thermoplastischen Rezyklaten - Teil
1: Begriffe
This European Standard was approved by CEN on 7 February 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14541-1:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 14541-1:2022
EN 14541-1:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Abbreviations . 8
Bibliography . 9
2
---------------------- Page: 4 ----------------------
SIST EN 14541-1:2022
EN 14541-1:2022 (E)
European foreword
This document (EN 14541-1:2022) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2022, and conflicting national standards shall
be withdrawn at the latest by November 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. C
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.