EN 13480-3:2017/A2:2020
(Amendment)Metallic industrial piping - Part 3: Design and calculation
Metallic industrial piping - Part 3: Design and calculation
Specifies the design and calculation of industrial metallic piping systems, including supports, covered by EN 13480. Revision of Clause 12 and Annex H related to Stress Intensification Factors SIF
Metallische industrielle Rohrleitungen - Teil 3: Konstruktion und Berechnung
Tuyauteries industrielles métalliques - Partie 3 : Conception et calcul
No scope available
Kovinski industrijski cevovodi - 3. del: Konstruiranje in izračun - Dopolnilo A2
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13480-3:2018/A2:2020
01-oktober-2020
Kovinski industrijski cevovodi - 3. del: Konstruiranje in izračun - Dopolnilo A2
Metallic industrial piping - Part 3: Design and calculation
Metallische industrielle Rohrleitungen - Teil 3: Konstruktion und Berechnung
Tuyauteries industrielles métalliques - Partie 3 : Conception et calcul
Ta slovenski standard je istoveten z: EN 13480-3:2017/A2:2020
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN 13480-3:2018/A2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13480-3:2018/A2:2020
---------------------- Page: 2 ----------------------
SIST EN 13480-3:2018/A2:2020
EN 13480-3:2017/A2
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2020
EUROPÄISCHE NORM
ICS 23.040.01
English Version
Metallic industrial piping - Part 3: Design and calculation
Tuyauteries industrielles métalliques - Partie 3 : Metallische industrielle Rohrleitungen - Teil 3:
Conception et calcul Konstruktion und Berechnung
This amendment A2 modifies the European Standard EN 13480-3:2017; it was approved by CEN on 12 July 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-3:2017/A2:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13480-3:2018/A2:2020
EN 13480-3:2017/A2:2020 (E)
Contents Page
European foreword . 4
1 Modification to 3.2, "Symbols and units" . 5
2 Modification to 4.2, "Loadings". 5
3 Modification to 4.3, "Thickness" . 5
4 Modification to 12.2.4.2, "Overstrained behaviour" . 6
5 Modification to 12.2.10.3, "Basic assumptions and requirements" . 6
6 Modification to 12.3, "Flexibility analysis" . 6
7 Modification to 12.3.2, "Stress due to sustained loads" . 8
8 Modification to 12.3.3, "Stress due to sustained and occasional or exceptional loads" . 9
9 Modification to 12.3.4, "Stress range due to thermal expansion and alternating loads" . 11
10 Modification to 12.3.5, "Additional conditions for the creep range" . 13
11 Modification to 12.3.6, "Stresses due to a single non-repeated support movement" . 13
12 Modification to 12.3.7, "Determination of resultant moments" . 14
13 Modification to 12.3.8, "Alternative method for stress calculation" . 16
14 Modification to 13.1.1, "General" . 16
15 Modification to 13.1.3.12, .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.