Rigid cellular plastics — Determination of compression properties

This document specifies methods for determining the compressive strength and corresponding relative deformation, the compressive stress at 10 % relative deformation, and the compressive modulus of rigid cellular plastics.

Plastiques alvéolaires rigides — Détermination des caractéristiques de compression

Le présent document spécifie des méthodes permettant de déterminer la résistance à la compression et la déformation relative correspondante, la contrainte en compression correspondant à 10 % de déformation relative et le module en compression des plastiques alvéolaires rigides.

General Information

Status
Published
Publication Date
30-Mar-2021
Current Stage
9092 - International Standard to be revised
Completion Date
29-Nov-2022
Ref Project

Relations

Buy Standard

Standard
ISO 844:2021 - Rigid cellular plastics -- Determination of compression properties
English language
15 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 844:2021 - Plastiques alvéolaires rigides -- Détermination des caractéristiques de compression
French language
15 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/PRF 844:Version 12-feb-2021 - Rigid cellular plastics -- Determination of compression properties
English language
15 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 844
Seventh edition
2021-03
Rigid cellular plastics —
Determination of compression
properties
Plastiques alvéolaires rigides — Détermination des caractéristiques
de compression
Reference number
ISO 844:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 844:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 844:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Principle . 3
6 Apparatus . 3
6.1 Compression-testing machine . 3
6.2 Devices for measuring displacement and force . 3
6.2.1 Measurement of displacement . 3
6.2.2 Measurement of force . 4
6.2.3 Calibration . 4
6.3 Instruments for measuring the dimensions of the test specimens . 4
7 Test specimens. 4
7.1 Dimensions . 4
7.2 Preparation . 5
7.3 Number . 5
7.4 Conditioning . 5
8 Procedure. 5
9 Expression of results . 6
9.1 General . 6
9.2 Compressive strength and corresponding relative deformation . 7
9.2.1 Compressive strength . 7
9.2.2 Nominal relative deformation (procedure A) . 7
9.2.3 Relative deformation (procedure B) . 8
9.3 Compressive stress at 10 % nominal relative deformation (procedure A) . 8
9.4 Nominal compressive modulus of elasticity (procedure A) . 8
9.5 Compressive modulus of elasticity (procedure B) . 9
10 Precision . 9
10.1 Procedure A . 9
10.2 Procedure B .10
11 Test report .11
Annex A (informative) Remarks about the determination of the compressive modulus .12
Bibliography .15
© ISO 2021 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 844:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 10, Cellular
plastics, in collaboration with the European Committee for Standardization (CEN) Technical Committee
CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This seventh edition cancels and replaces the sixth edition (ISO 844:2014), which has been technically
revised. The main changes compared to the previous edition are as follows:
— different extensometer gage lengths have been given for use with different specimen thicknesses;
— repeatability and reproducibility results from the interlaboratory test on Procedure B have been
added for compressive strength and compressive modulus of elasticity measurements;
— Annex A has been added to provide information on the determination of the compressive modulus
by means Procedure B.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 844:2021(E)
Rigid cellular plastics — Determination of compression
properties
1 Scope
This document specifies methods for determining the compressive strength and corresponding relative
deformation, the compressive stress at 10 % relative deformation, and the compressive modulus of
rigid cellular plastics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 1923, Cellular plastics and rubbers — Determination of linear dimensions
ISO 7500-1, Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1:
Tension/compression testing machines — Calibration and verification of the force-measuring system
ISO 9513, Metallic materials — Calibration of extensometer systems used in uniaxial testing
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
nominal relative deformation (procedure A)
ε
C
ratio of the reduction (in relation to its initial value) in thickness of the test specimen
Note 1 to entry: It is expressed as a percentage.
Note 2 to entry: ε is the nominal relative deformation corresponding to σ (see 3.3).
Cm m
3.2
relative deformation (procedure B)
ε
ratio of the reduction (in relation to its initial value) of extensometer gauge length
Note 1 to entry: It is expressed as a percentage.
Note 2 to entry: ε is the relative deformation corresponding to σ (see 3.3).
m m
© ISO 2021 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 844:2021(E)

3.3
compressive strength
σ
m
maximum compressive force F divided by the initial cross-sectional area A of the test specimen when
m 0
the relative deformation ε and the nominal relative deformation ε respectively is < 10 %
C
Note 1 to entry: It is expressed in megapascals (MPa).
3.4
compressive stress at 10 % nominal relative deformation (procedure A)
σ
C10
ratio of the compressive force F at 10 % nominal relative deformation ε to the initial cross-sectional
10 C10
area of the test specimen
Note 1 to entry: It is expressed in megapascals (MPa).
3.5
nominal compressive modulus of elasticity (procedure A)
E
C
difference in compressive stress divided by the difference in corresponding nominal relative
deformation below the proportional limit, i.e. when the relation is linear
Note 1 to entry: It is expressed in megapascals (MPa).
3.6
compressive modulus of elasticity (procedure B)
E
difference in compressive stress divided by the corresponding difference in relative deformation below
the proportional limit, i.e. when the relation is linear
Note 1 to entry: It is expressed in megapascals (MPa).
3.7
conventional proportional limit
X
e
upper limit of the linear part of the force - deformation curve
Note 1 to entry: It is expressed in millimetres (mm).
4 Symbols
Symbol Definition Unit
A initial cross-sectional area in square milli-
0
metres
E compressive modulus of elasticity in megapascals
E nominal compressive modulus of elasticity in megapascals
C
F force corresponding to x (conventional proportional limit) in newtons
e e
F force corresponding to x (nominal proportional limit) in newtons
Ce Ce
F maximum force in newtons
m
F force at 10 % nominal relative deformation in newtons
10
h initial thickness of test specimen (Procedure A) in millimetres
0
l initial gauge length of the extensometer (Procedure B) in millimetres
o
Ra surface roughness
t thickness
X displacement at F in the conventional elastic zone, (Procedure B) in millimetres
e e
X nominal displacement at F in the conventional elastic zone, (Procedure A) in millimetres
Ce Ce
2 © ISO 2021 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 844:2021(E)

Symbol Definition Unit
X displacement at maximum force in millimetres
m
X nominal displacement at maximum force in millimetres
Cm
X displacement at 10 % nominal relative deformation in millimetres
C10
ε relative deformation corresponding to compressive strength σ in percent
m m
ε nominal relative deformation corresponding to compressive strength σ in percent
Cm m
ε 10 % nominal relative deformation in percent
C10
σ compressive strength in megapascals
m
σ compressive stress at 10 % nominal relative deformation in megapascals
10
5 Principle
A compressive force is applied in an axial direction and perpendicular to the faces of test specimen.
There are two procedures:
— Procedure A employs crosshead motion for determination of compressive properties. Procedure A
shall be used to determine:
— compressive strength and the corresponding nominal relative deformation;
— compressive stress at 10 % nominal relative deformation;
— nominal compressive modulus.
— Procedure B employs strain measuring devices connected to the specimen (contact or optical
extensometer) or similar device which directly measures the specimen deformation. Procedure B
shall be used to determine:
— compressive strength and the corresponding relative deformation;
— compressive modulus.
6 Apparatus
6.1 Compression-testing machine
Use a compression-testing machine suited to the range of force and displacement involved and
having two square or circular plane, parallel plates which are polished and cannot be deformed. The
compression plates shall be of any convenient size which ensures that test specimens are compressed
over their whole areas. The following conditions have been found acceptable:
a) surface roughness of Ra ≤ 0,4 µm;
b) steel plate thickness of t ≥ 8 mm in the loading direction;
c) in case of thin samples, platens dimensions shall be so that clip on short travel extensometers with
stop stud, can be appropriately clamped to the specimen when it is put in the centre of the platens.
6.2 Devices for measuring displacement and force
6.2.1 Measurement of displacement
6.2.1.1 Procedure A — The compression-testing machine shal
...

NORME ISO
INTERNATIONALE 844
Septième édition
2021-03
Plastiques alvéolaires rigides —
Détermination des caractéristiques de
compression
Rigid cellular plastics — Determination of compression properties
Numéro de référence
ISO 844:2021(F)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 844:2021(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2021 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 844:2021(F)

Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Symboles . 2
5 Principe . 3
6 Appareillage . 3
6.1 Machine d’essai de compression . 3
6.2 Dispositifs de mesurage du déplacement et de la force . 4
6.2.1 Mesurage du déplacement . 4
6.2.2 Mesurage de la force . 4
6.2.3 Étalonnage . 4
6.3 Matériel de mesurage des dimensions des éprouvettes . 4
7 Éprouvettes . 4
7.1 Dimensions . 4
7.2 Préparation . 5
7.3 Nombre . 5
7.4 Conditionnement . 5
8 Mode opératoire. 5
9 Expression des résultats. 6
9.1 Généralités . 6
9.2 Résistance à la compression et déformation relative correspondante . 7
9.2.1 Résistance à la compression . 7
9.2.2 Déformation relative nominale (Mode opératoire A) . 7
9.2.3 Déformation relative (Mode opératoire B) . 8
9.3 Contrainte en compression correspondant à 10 % de déformation relative
nominale (Mode opératoire A) . 8
9.4 Module d’élasticité en compression nominal (Mode opératoire A) . 8
9.5 Module d’élasticité en compression (Mode opératoire B) . 9
10 Fidélité . 9
10.1 Mode opératoire A . 9
10.2 Mode opératoire B .10
11 Rapport d’essai .11
Annexe A (informative) Remarques sur la détermination du module en compression .12
Bibliographie .15
© ISO 2021 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 844:2021(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 61, Plastiques, sous-comité SC 10,
Plastiques alvéolaires, en collaboration avec le comité technique CEN/TC 249, Plastiques, du Comité
européen de normalisation (CEN) conformément à l’Accord de coopération technique entre l’ISO et le
CEN (Accord de Vienne).
Cette septième édition annule et remplace la sixième édition (ISO 844:2014), qui a fait l’objet d’une
révision technique. Les principales modifications par rapport à l’édition précédente sont les suivantes:
— différentes longueurs de référence de l’extensomètre ont été données pour une utilisation avec
différentes épaisseurs d'éprouvette;
— les résultats de répétabilité et de reproductibilité de l'essai interlaboratoires sur le Mode
opératoire B ont été ajoutés pour la résistance à la compression et le module de compression des
mesures d'élasticité;
— l'Annexe A a été ajoutée pour fournir des informations sur la détermination du module de compression
au moyen du Mode opératoire B.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2021 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 844:2021(F)
Plastiques alvéolaires rigides — Détermination des
caractéristiques de compression
1 Domaine d’application
Le présent document spécifie des méthodes permettant de déterminer la résistance à la compression
et la déformation relative correspondante, la contrainte en compression correspondant à 10 % de
déformation relative et le module en compression des plastiques alvéolaires rigides.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s'applique (y compris les
éventuels amendements).
ISO 291, Plastiques — Atmosphères normales de conditionnement et d’essai
ISO 1923, Plastiques et caoutchoucs alvéolaires — Détermination des dimensions linéaires
ISO 7500-1, Matériaux métalliques — Étalonnage et vérification des machines pour essais statiques
uniaxiaux — Partie 1: Machines d’essai de traction/compression — Étalonnage et vérification du système
de mesure de force
ISO 9513, Matériaux métalliques — Étalonnage des chaînes extensométriques utilisées lors d’essais
uniaxiaux
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/
3.1
déformation relative nominale (Mode opératoire A)
ε
C
rapport de la diminution d’épaisseur de l’éprouvette (par rapport à sa valeur initiale)
Note 1 à l'article: Elle est exprimée en pourcentage.
Note 2 à l'article: ε est la déformation relative nominale correspondant à σ (voir 3.3).
Cm m
3.2
déformation relative (Mode opératoire B)
ε
rapport de la diminution de la longueur de référence de l’extensomètre (par rapport à sa valeur initiale)
Note 1 à l'article: Elle est exprimée en pourcentage.
Note 2 à l'article: ε est la déformation relative correspondant à σ (voir 3.3).
m m
© ISO 2021 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 844:2021(F)

3.3
résistance à la compression
σ
m
rapport de la force maximale de compression F à l’aire initiale de la section transversale de l’éprouvette
m
A lorsque la déformation relative ε ou la déformation relative nominale ε , respectivement, est < 10 %
0 C
Note 1 à l'article: Elle est exprimée en mégapascals (MPa).
3.4
contrainte en compression correspondant à 10 % de déformation relative nominale (Mode
opératoire A)
σ
C10
rapport de la force de compression F correspondant à 10 % de déformation relative nominale ε , à
10 C10
l’aire initiale de la section transversale de l’éprouvette
Note 1 à l'article: Elle est exprimée en mégapascals (MPa).
3.5
module d’élasticité en compression nominal (Mode opératoire A)
E
C
rapport de la différence de contrainte en compression à la différence de déformation relative nominale
correspondante en deçà de la limite proportionnelle, c’est-à-dire quand la relation est linéaire
Note 1 à l'article: Il est exprimé en mégapascals (MPa).
3.6
module d’élasticité en compression (Mode opératoire B)
E
rapport de la différence de contrainte en compression à la différence de déformation relative
correspondante en deçà de la limite proportionnelle, c’est-à-dire quand la relation est linéaire
Note 1 à l'article: Il est exprimé en mégapascals (MPa).
3.7
limite proportionnelle conventionnelle
X
e
limite supérieure de la partie linéaire de la courbe force-déformation
Note 1 à l'article: Elle est exprimée en millimètres (mm).
4 Symboles
Symbole Définition Unité
A aire initiale de la section transversale en millimètres
0
carrés
E module d’élasticité en compression en mégapascals
E module d’élasticité en compression nominal en mégapascals
C
F force correspondant à x (limite proportionnelle conventionnelle) en newtons
e e
F force correspondant à x (limite proportionnelle nominale) en newtons
Ce Ce
F force maximale en newtons
m
F force correspondant à 10 % de déformation relative nominale en newtons
10
h épaisseur initiale de l’éprouvette (Mode opératoire A) en millimètres
0
l longueur de référence initiale de l’extensomètre (Mode opératoire B) en millimètres
o
Ra rugosité de surface
t épaisseur
2 © ISO 2021 – Tous droits réservés

---------------------- Page: 6 ----------------------
ISO 844:2021(F)

Symbole Définition Unité
X déplacement correspondant à F dans la zone conventionnelle d’élasticité, (Mode en millimètres
e e
opératoire B)
X déplacement nominal correspondant à F dans la zone conventionnelle d’élasti- en millimètres
Ce Ce
cité, (Mode opératoire A)
X déplacement correspondant à la force maximale en millimètres
m
X déplacement nominal correspondant à la force maximale en millimètres
Cm
X déplacement correspondant à 10 % de déformation relative nominale en millimètres
C10
ε déformation relative correspondant à la résistance à la compression σ en pourcentage
m m
ε déformation relative nominale correspondant à la résistance à la compression σ en pourcentage
Cm m
ε 10 % de déformation relative nominale en pourcentage
C10
σ résistance à la compression en mégapascals
m
σ contrainte en compression correspondant à 10 % de déformation relative nominale en mégapascals
10
5 Principe
Une force de compression est appliquée dans une direction axiale, perpendiculairement aux faces de
l’éprouvette.
Il existe deux modes opératoires:
— le Mode opératoire A utilise le mouvement de la traverse pour la détermination des caractéristiques
de compression. Le Mode opératoire A doit être utilisé pour déterminer:
— la résistance à la compression et la déformation relative nominale correspondante;
— la contrainte en compression correspondant à 10 % de déformation relative nominale;
— le module d’élasticité en compression nominal.
— le Mode opératoire B utilise des dispositifs de mesure de la déformation raccordés à l’éprouvette
(extensomètre par contact ou optique) ou un dispositif similaire qui mesure directement la
déformation de l’éprouvette. Le Mode opératoire B doit être utilisé pour déterminer:
— la résistance à la compression et la déformation relative correspondante;
— le module en compression.
6 Appareillage
6.1 Machine d’essai de compression
Utiliser une machine d’essai de compression appropriée à la gamme de force et de déplacement à
mettre en œuvre, munie de deux plateaux parallèles, de forme carrée ou circulaire, de surface plane et
polie et indéformables. Les plateaux de compression doivent avoir une dimension pratique qui assure
que les éprouvettes sont comprimées sur toute leur surface. Les conditions suivantes ont été jugées
acceptables:
a) rugosité de surface Ra ≤ 0,4 µm;
b) plateau en acier d’une épaisseur t ≥ 8 mm dans la direction de mise en charge;
c) pour des échantillons fins, les dimensions des plateaux doivent permettent de fixer correctement
à l’aide d’un goujon d’arrêt l’attache des extensomètres mesurant de petits déplacements sur
l’éprouvette lorsqu’elle se trouve au centre des plateaux.
© ISO 2021 – Tous droits réservés 3

---------------------- Page: 7 ----------------------
ISO 844:2021(F)

6.2 Dispositifs de mesurage du déplacement et de la force
6.2.1 Mesurage du déplacement
6.2.1.1 Mode opératoire A — La machine d’essai de compression doit être pourvue d’un système
permettant le mesurage en continu du déplacement x du plateau mobile avec une exactitude de
...

INTERNATIONAL ISO
STANDARD 844
Seventh edition
Rigid cellular plastics —
Determination of compression
properties
Plastiques alvéolaires rigides — Détermination des caractéristiques
de compression
PROOF/ÉPREUVE
Reference number
ISO 844:2021(E)
©
ISO 2021

---------------------- Page: 1 ----------------------
ISO 844:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 844:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 Principle . 3
6 Apparatus . 3
6.1 Compression-testing machine . 3
6.2 Devices for measuring displacement and force . 3
6.2.1 Measurement of displacement . 3
6.2.2 Measurement of force . 4
6.2.3 Calibration . 4
6.3 Instruments for measuring the dimensions of the test specimens . 4
7 Test specimens. 4
7.1 Dimensions . 4
7.2 Preparation . 5
7.3 Number . 5
7.4 Conditioning . 5
8 Procedure. 5
9 Expression of results . 6
9.1 General . 6
9.2 Compressive strength and corresponding relative deformation . 7
9.2.1 Compressive strength . 7
9.2.2 Nominal relative deformation (procedure A) . 7
9.2.3 Relative deformation (procedure B) . 8
9.3 Compressive stress at 10 % nominal relative deformation (procedure A) . 8
9.4 Nominal compressive modulus of elasticity (procedure A) . 9
9.5 Compressive modulus of elasticity (procedure B) . 9
10 Precision .10
10.1 Procedure A .10
10.2 Procedure B .10
11 Test report .11
Annex A (informative) Remarks about the determination of the compressive modulus .12
Bibliography .15
© ISO 2021 – All rights reserved PROOF/ÉPREUVE iii

---------------------- Page: 3 ----------------------
ISO 844:2021(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 10, Cellular
plastic, in collaboration with the European Committee for Standardization (CEN) Technical Committee
CEN/TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This seventh edition cancels and replaces the sixth edition (ISO 844:2014), which has been technically
revised. The main changes compared to the previous edition are as follows:
— different extensometer gage lengths have been given for use with different specimen thicknesses;
— repeatability and reproducibility results from the interlaboratory test on Procedure B have been
added for compressive strength and compressive modulus of elasticity measurements;
— Annex A has been added to provide information on the determination of the compressive modulus
by means Procedure B.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 844:2021(E)
Rigid cellular plastics — Determination of compression
properties
1 Scope
This document specifies methods for determining the compressive strength and corresponding relative
deformation, the compressive stress at 10 % relative deformation, and the compressive modulus of
rigid cellular plastics.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 1923, Cellular plastics and rubbers — Determination of linear dimensions
ISO 7500-1, Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1:
Tension/compression testing machines — Calibration and verification of the force-measuring system
ISO 9513, Metallic materials — Calibration of extensometer systems used in uniaxial testing
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
nominal relative deformation (procedure A)
ε
C
ratio of the reduction (in relation to its initial value) in thickness of the test specimen
Note 1 to entry: It is expressed as a percentage.
Note 2 to entry: ε is the nominal relative deformation corresponding to σ (see 3.3).
Cm m
3.2
relative deformation (procedure B)
ε
ratio of the reduction (in relation to its initial value) of extensometer gauge length
Note 1 to entry: It is expressed as a percentage.
Note 2 to entry: ε is the relative deformation corresponding to σ (see 3.3).
m m
© ISO 2021 – All rights reserved PROOF/ÉPREUVE 1

---------------------- Page: 5 ----------------------
ISO 844:2021(E)

3.3
compressive strength
σ
m
maximum compressive force F divided by the initial cross-sectional area A of the test specimen when
m 0
the relative deformation ε and the nominal relative deformation ε respectively is < 10 %
C
Note 1 to entry: It is expressed in megapascals (MPa).
3.4
compressive stress at 10 % nominal relative deformation (procedure A)
σ
C10
ratio of the compressive force F at 10 % nominal relative deformation ε to the initial cross-sectional
10 C10
area of the test specimen
Note 1 to entry: It is expressed in megapascals (MPa).
3.5
nominal compressive modulus of elasticity (procedure A)
E
C
difference in compressive stress divided by the difference in corresponding nominal relative
deformation below the proportional limit, i.e. when the relation is linear
Note 1 to entry: It is expressed in megapascals (MPa).
3.6
compressive modulus of elasticity (procedure B)
E
difference in compressive stress divided by the corresponding difference in relative deformation below
the proportional limit, i.e. when the relation is linear
Note 1 to entry: It is expressed in megapascals (MPa).
3.7
conventional proportional limit
X
e
upper limit of the linear part of the force - deformation curve
Note 1 to entry: It is expressed in millimetres (mm).
4 Symbols
Symbol Definition Unit
A initial cross-sectional area, in square milli-
0
metres
E compressive modulus of elasticity, in megapascals
E nominal compressive modulus of elasticity in megapascals
C
F force corresponding to x (conventional proportional limit) in newtons
e e
F force corresponding to x (nominal proportional limit), in newtons
Ce Ce
F maximum force, in newtons
m
F force at 10 % nominal relative deformation, in newtons
10
h initial thickness of test specimen (Procedure A), in millimetres
0
l initial gauge length of the extensometer (Procedure B), in millimetres
o
Ra surface roughness
t thickness
X displacement at F in the conventional elastic zone, (Procedure B) in millimetres
e e
X nominal displacement at F in the conventional elastic zone, (Procedure A) in millimetres
Ce Ce
2 PROOF/ÉPREUVE © ISO 2021 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 844:2021(E)

Symbol Definition Unit
X displacement at maximum force, in millimetres
m
X nominal displacement at maximum force, in millimetres
Cm
X displacement at 10 % nominal relative deformation, in millimetres
C10
ε relative deformation corresponding to compressive strength σ , in percent
m m
ε nominal relative deformation corresponding to compressive strength σ , in percent
Cm m
ε 10 % nominal relative deformation, in percent
C10
σ compressive strength, in megapascals
m
σ compressive stress at 10 % nominal relative deformation, in megapascals
10
5 Principle
A compressive force is applied in an axial direction and perpendicular to the faces of test specimen.
There are two procedures:
— Procedure A employs crosshead motion for determination of compressive properties. Procedure A
shall be used to determine:
— compressive strength and the corresponding nominal relative deformation;
— compressive stress at 10 % nominal relative deformation;
— nominal compressive modulus.
— Procedure B employs strain measuring devices connected to the specimen (contact or optical
extensometer) or similar device which directly measures the specimen deformation. Procedure B
shall be used to determine:
— compressive strength and the corresponding relative deformation;
— compressive modulus.
6 Apparatus
6.1 Compression-testing machine
Use a compression-testing machine suited to the range of force and displacement involved and
having two square or circular plane, parallel plates which are polished and cannot be deformed. The
compression plates shall be of any convenient size which ensures that test specimens are compressed
over their whole areas. The following conditions have been found acceptable:
a) Surface roughness of Ra ≤ 0,4 µm;
b) Steel plate thickness of t ≥ 8 mm in the loading direction;
c) In case of thin samples, platens dimensions shall be so that clip on short travel extensometers with
stop stud, can be appropriately clamped to the specimen when it is put in the centre of the platens.
6.2 Devices for measuring displacement and force
6.2.1 Measurement of displacement
6.2.1.1 Procedure A — The compression-testing machine shall be fitted with a system allowing
continuous measu
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.